Contact Us | Language: čeština English
dc.title | The effect of polymer pin ribs on reinforcement of sandwich structures | en |
dc.contributor.author | Fojtl, Ladislav | |
dc.contributor.author | Maňas, Lukáš | |
dc.contributor.author | Rusnáková, Soňa | |
dc.relation.ispartof | Manufacturing Technology | |
dc.identifier.issn | 1213-2489 Scopus Sources, Sherpa/RoMEO, JCR | |
dc.date.issued | 2018 | |
utb.relation.volume | 18 | |
utb.relation.issue | 6 | |
dc.citation.spage | 889 | |
dc.citation.epage | 894 | |
dc.type | article | |
dc.language.iso | en | |
dc.publisher | Univerzita J. E. Purkyně v Ústí nad Labem (UJEP) | |
dc.identifier.doi | 10.21062/ujep/196.2018/a/1213-2489/mt/18/6/889 | |
dc.subject | edgewise compression | en |
dc.subject | flexural properties | en |
dc.subject | foam core | en |
dc.subject | polymer rib | en |
dc.subject | sandwich structure | en |
dc.subject | vacuum infusion | en |
dc.description.abstract | This research paper deals with an influence of reinforcing polymer ribs on selected mechanical properties of sandwich structures. Reinforcing epoxy ribs are produced directly by the vacuum infusion technology when resin during its flow fills the prepared holes in the polymer core. In the experiment, two rib sizes (diameters) were tested as well as two variants of hole patterns on the core surface. The possible influence of the core material was evaluated on two core material types with different thicknesses. In addition to the observed mechanical properties observed, the types of failure and changes of the sandwich panels weight were also characterized. The obtained results show a significant increase in flexural strength and stiffness of all types and shapes of prepared reinforcing polymer ribs. Positive effect was also observed in the case of edgewise compression load capacity. © 2018. Published by Manufacturing Technology. | en |
utb.faculty | Faculty of Technology | |
utb.faculty | University Institute | |
dc.identifier.uri | http://hdl.handle.net/10563/1008451 | |
utb.identifier.rivid | RIV/70883521:28610/18:63521087!RIV19-TA0-28610___ | |
utb.identifier.rivid | RIV/70883521:28610/18:63521087!RIV19-MSM-28610___ | |
utb.identifier.rivid | RIV/70883521:28110/18:63521087!RIV19-TA0-28110___ | |
utb.identifier.rivid | RIV/70883521:28110/18:63521087!RIV19-MSM-28110___ | |
utb.identifier.obdid | 43879401 | |
utb.identifier.scopus | 2-s2.0-85059331365 | |
utb.source | j-scopus | |
dc.date.accessioned | 2019-07-08T11:59:47Z | |
dc.date.available | 2019-07-08T11:59:47Z | |
utb.ou | Centre of Polymer Systems | |
utb.contributor.internalauthor | Fojtl, Ladislav | |
utb.contributor.internalauthor | Maňas, Lukáš | |
utb.contributor.internalauthor | Rusnáková, Soňa | |
utb.fulltext.affiliation | Ladislav Fojtl 1,2, Lukas Manas 1,2, Sona Rusnakova 1 1 Department of Production Engineering, Faculty of Technology, Tomas Bata University in Zlín. Vavrečkova 275, 760 01 Zlín. Czech Republic. E-mail: fojtl@ft.utb.cz, rusnakova@ft.utb.cz, zaludek@ft.utb.cz 2 Centre of Polymer Systems, Tomas Bata University in Zlín, Trida Tomase Bati 5678, 760 01 Zlín, Czech Republic | |
utb.fulltext.dates | - | |
utb.scopus.affiliation | Department of Production Engineering, Faculty of Technology, Tomas Bata University in Zlín, Vavreckova 275, Zlín, 760 01, Czech Republic; Centre of Polymer Systems, Tomas Bata University inZlín, Trida Tomase Bati 5678, Zlín, 760 01, Czech Republic | |
utb.fulltext.faculty | Faculty of Technology | |
utb.fulltext.faculty | Faculty of Technology | |
utb.fulltext.faculty | Faculty of Technology | |
utb.fulltext.ou | Department of Production Engineering | |
utb.fulltext.ou | Centre of Polymer Systems | |
utb.fulltext.ou | Department of Production Engineering | |
utb.fulltext.ou | Centre of Polymer Systems | |
utb.fulltext.ou | Department of Production Engineering |