Measuring of temperature and pressure in injection mold

Kyas, Kamil; Černý, Jakub; Staněk, Michal; Maňas, Miroslav; Maňas, David; Šenkeřík, Vojtěch; Škrobák, Adam

dc.title	Measuring of temperature and pressure in injection mold	en
dc.contributor.author	Kyas, Kamil
dc.contributor.author	Černý, Jakub
dc.contributor.author	Staněk, Michal
dc.contributor.author	Maňas, Miroslav
dc.contributor.author	Maňas, David
dc.contributor.author	Šenkeřík, Vojtěch
dc.contributor.author	Škrobák, Adam
dc.relation.ispartof	International Journal of Mathematics and Computers in Simulation
dc.identifier.issn	1998-0159 Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2012
utb.relation.volume	6
utb.relation.issue	6
dc.citation.spage	600
dc.citation.epage	607
dc.type	article
dc.language.iso	en
dc.publisher	North Atlantic University Union (NAUN)	en
dc.relation.uri	http://www.naun.org/multimedia/NAUN/mcs/16-600.pdf
dc.subject	Cure rate	en
dc.subject	Injection mold	en
dc.subject	Injection molding process	en
dc.subject	Pressure sensor	en
dc.subject	Rubber compound	en
dc.subject	Temperature sensor	en
dc.description.abstract	Injection molding is one of the most widespread technologies in polymer process. This technology has enough advantages in rubber industry too. This article compare results from temperature/pressure sensors in real process with flow analyses in computational software. These received dates should be helpful and advantageous for the polymeric industry, especially rubber industry. The product's production cycle can be shorted with right setting of process. Using sensors and flow analyze can be good way for right process setting.	en
utb.faculty	Faculty of Technology
utb.faculty	Faculty of Applied Informatics
dc.identifier.uri	http://hdl.handle.net/10563/1003198
utb.identifier.rivid	RIV/70883521:28110/12:43869135!RIV13-MSM-28110___
utb.identifier.rivid	RIV/70883521:28140/12:43869135!RIV13-MSM-28140___
utb.identifier.obdid	43869366
utb.identifier.scopus	2-s2.0-84875713640
utb.source	j-scopus
dc.date.accessioned	2013-04-29T12:17:47Z
dc.date.available	2013-04-29T12:17:47Z
utb.contributor.internalauthor	Kyas, Kamil
utb.contributor.internalauthor	Černý, Jakub
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Maňas, Miroslav
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Šenkeřík, Vojtěch
utb.contributor.internalauthor	Škrobák, Adam
utb.fulltext.affiliation	K. Kyas, J. Cerny, M. Stanek, M. Manas, D. Manas, V. Senkerik and A. Skrobak Kamil Kyas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (phone: +420576035153; fax: +420576035176; e-mail: kyas@ft.utb.cz). Jakub Cerny is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: j1cerny@ft.utb.cz). Michal Stanek is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: stanek@ft.utb.cz). David Manas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: dmanas@ft.utb.cz). Miroslav Manas is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: manas@ft.utb.cz). Vojtech Senkerik is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: senkerik@ft.utb.cz). Adam Skrobak is with the Tomas Bata University in Zlin, nam. T. G. Masaryka 5555, 76001 Zlin, Czech Republic (e-mail: skrobak@ft.utb.cz).
utb.fulltext.dates	-
utb.fulltext.sponsorship	This paper is supported by the internal grant of TBU in Zlin No. IGA/FT/2012/041 funded from the resources of specific university research and by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089.
utb.fulltext.faculty	-
utb.fulltext.ou	-