TBU Publications
Repository of TBU Publications

The effect of injection molding on physical properties of EPDM rubber

DSpace Repository

Show simple item record


dc.title The effect of injection molding on physical properties of EPDM rubber en
dc.contributor.author Škrobák, Adam
dc.contributor.author Šenkeřík, Vojtěch
dc.contributor.author Janoštík, Václav
dc.relation.ispartof MATEC Web of Conferences
dc.identifier.issn 2261-236X Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued 2018
utb.relation.volume 210
dc.event.title 22nd International Conference on Circuits, Systems, Communications and Computers, CSCC 2018
dc.event.location Majorca
utb.event.state-en Spain
utb.event.state-cs Španělsko
dc.event.sdate 2018-07-14
dc.event.edate 2018-07-17
dc.type conferenceObject
dc.language.iso en
dc.publisher EDP Sciences
dc.identifier.doi 10.1051/matecconf/201821002039
dc.relation.uri https://www.matec-conferences.org/articles/matecconf/abs/2018/69/matecconf_cscc2018_02039/matecconf_cscc2018_02039.html
dc.description.abstract The paper a part of research aimed at the alternative of preparing test samples by injection molding. Such an alternative could bring more objective results in the field of testing samples produced in the same technology. The research is aimed at changing the preparation of rubber testing samples-replacing the standard method according to ISO 23529 by the injection method, especially with the use of rubber compounds for injection molding. This article compares and evaluates the selected physical properties (tensile strength and tear strength) of EPDM rubber injection molded samples with samples prepared by the standard method-cutting out of a compression molded plate. The results have shown that using the injection molded samples we will achieve more objective results mainly to determine the tear strength. In the case of tensile strength, the differences are not so significant. © 2018 The Authors, published by EDP Sciences. en
utb.faculty Faculty of Applied Informatics
dc.identifier.uri http://hdl.handle.net/10563/1008313
utb.identifier.obdid 43878997
utb.identifier.scopus 2-s2.0-85055519483
utb.identifier.wok 000567668400045
utb.source d-scopus
dc.date.accessioned 2019-01-03T12:31:44Z
dc.date.available 2019-01-03T12:31:44Z
dc.description.sponsorship European Regional Development Fund under the project CEBIA-Tech Instrumentation [CZ.1.05/2.1.00/19.0376]; Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Program [L01303 (MSMT-7778/2014)]; Internal Grant Agency of TBU in Zlin [IGA/FT/2018/012]
dc.rights Attribution 4.0 International
dc.rights.uri https://creativecommons.org/licenses/by/4.0/
dc.rights.access openAccess
utb.contributor.internalauthor Škrobák, Adam
utb.contributor.internalauthor Šenkeřík, Vojtěch
utb.contributor.internalauthor Janoštík, Václav
utb.fulltext.affiliation Adam Skrobak 1,a, Vojtech Senkerik 1, Vaclav Janostik 1 1 Tomas Bata Univerzity in Zlin, TGM 5555, 760 01 Zlin, Czech Republic a Corresponding author: skrobak@ft.utb.cz
utb.fulltext.dates -
utb.wos.affiliation [Skrobak, Adam; Senkerik, Vojtech; Janostik, Vaclav] Tomas Bata Univ Zlin, TGM 5555, Zlin 76001, Czech Republic
utb.scopus.affiliation Tomas Bata Univerzity in Zlin, TGM 5555, Zlin, 760 01, Czech Republic
Find Full text

Files in this item

Show simple item record

Attribution 4.0 International Except where otherwise noted, this item's license is described as Attribution 4.0 International